" they're having us do projects of our own choice"
I'm going to put a stereo amp into my helmet (to hear better), but I'm afraid of it amplifying loud sounds too much. So I've been looking for a Auto Gain Control circuit, to squelch the volume when needed, but haven't found one that meets my needs.
How about that for a project?
"i was going to wire up some LEDS soon but was curious as to what resistor i would need."
May I recommend this site:
Thinking about you guys . You could twist wires onto LEDs for your light project, but if you want a long term solution you HAVE to solder the wiring.
This is the best soldering tutorial I have ever found. Way better then most college classes on the subject.
Hey is anyone here Any good with building computer systems or writing code to make stuff work? I want to add a few things to the helmet for LCF purposes and but I lack the technical ability to do what I want. I've seen a few of you guys put cool looking comms attachments on your helmet and I was watching The Forgotten Spartans on YouTube (machinima) and one of the dudes had a com unit on one side and what looked like a projector on the other. I thought that would be cool to have a working com unit so if you go with buddy's you have Coms. And the projector would be near to display a map and set an objective or RV point if any one got lost. Idk if anyone can help let me know.
I am an electronics Engineer...
Com system isnt that complicated. You could buy a motorcycle com system and attach it inside your helmet. Done.
I am not sure, what exactly you want to do with a projector. If you have a stationary map and want to point sth out. No problem.
But if you have a map in your hand or even want a "display" inside your helmet like the real spartans... That would be really difficult and most of all very expensive. And I mean very very expensive.
I destroyed another servo. I could use some ideas . . . .
Repost from 1 March:
On my Spartan Laser I used an RC aircraft landing gear retract servo to retract and extend the shroud. To do so, I removed the electronics from the servo and wired the motor directly using a DPDT switch to control direction and a limit switch to cut off power. The limit switch has proved less than reliable, leading to a burnt out servo motor. Is there a SIMPLE way to pulse the new servo and get it to do its business as intended without me gutting it and having to rely on my analog cutoff?
Someone suggested buying a servo tester and gutting it for this functionality, but I believe those are geared for calibrating standard servos, not testing retracts.
EDIT 27 Mar: I ordered up a pair (plus a spare) of mini servo testers hoping I can set one to deliver an open pulse (pulse length well above neutral) when powered and the other to deliver a close pulse (Pulse length well above neutral) when powered. I'll keep the DPDT switch to power/depower the two circuits and drive the unmodified servo. Anyone with actual RC or robotics experience please tell me why this will or won't work. Any tips or pointers would be welcome.
Last edited by Redshirt; Mar 27, 2014 at 10:04 AM.
Wish I could help. I have used servos exactly once. I will say this on reversing the motion, shouldn't you be using an H-bridge to reverse the voltage to the motor?
If I have two fans in my helmet, should I have one blowing in and one blowing out, both blowing in or both blowing out?
Anyone have suggestions for LED panels, or lights. Been looking into getting some in my suit, I'm just not sure what gives the look. Thanks in advanced.
Might be able to use them for something. :P
Check the video in my signature, dollar store reading lights are easy to work with. Diffuse them with any plastic you can get your hands on.
A step up from that are pre-wired LED pigtails that you can purchase on eBay. A 12 volt prewired LED will run on a common 9 volt battery.
Lastly, the most hands on approach is a visit to radioshack or similar, and buy some LEDs, resisters, and battery clips. Then solder up the wiring to add to your suit. This thread has lots of discussion on what LEDs and resistor values to choose.
Another eBay link. Pre wired LEDs, each with a 9volt battery clip. A little wasteful, as you can wire them yourself and run multiple LEDs on a single 9 volt battery. But this is a quick and dirty way to get your suit to light up.
Last edited by thatdecade; Jun 4, 2014 at 9:56 PM.
I know there is a stickies index, but those threads should also be sticked, for real
Hey guys, I just put up a thread for my energy sword wiring here http://www.405th.com/f21/stuck-energ...llation-43381/
I'm stuck and need help with the circuit, I'm pretty dumb when it comes to electronics.
Thanks in advance for the help
Here's a video explaining my set-up https://www.youtube.com/watch?v=MoYG...ature=youtu.be
Assuming those are standard 12 volt LED strips. They actually have resistors built in. You can connect the 9 volt directly to the strip. Wire them in parallel to the 9 volt. You may need a second 9 volt to brighten the LEDs.