The Death Angel
Member
Hi there, this is my first pepakura project 
TDA ODST Buid
- Thread starter The Death Angel
- Start date
- Status
Hyperballistik
Well-Known Member
Nice job on the peps
The Death Angel
Member
Thank you, i think the EVA is hard a little bit more, and the eva is the hardest.
Thanks
of course the visor is momentarily here
this is what I used to mold for the visor, it's made in a very hard capboard, the back of a drawing folder, the proto-visor is made from a transparent pvc, 0,25mm.
Your helmet looks very good so far!
I don't know if you already have something in mind for your visor, but there's an excellent tutorial by ZakuAce right here http://www.405th.com/showthread.php/...-3-ODST-Visors It's cheap and easy to do! It's what I used for my visor (you can see pictures of the finished helmet in my thread, link in signature).
Aside from that, extremely clean pepping! Good job!
I don't know if you already have something in mind for your visor, but there's an excellent tutorial by ZakuAce right here http://www.405th.com/showthread.php/...-3-ODST-Visors It's cheap and easy to do! It's what I used for my visor (you can see pictures of the finished helmet in my thread, link in signature).
Aside from that, extremely clean pepping! Good job!
The Death Angel
Member
Yes, i seen the tutorial only now, the visor was a prototipe, made with the Hair dryer, but tomorrow i try the ZakuAce metod
I lied, it isn't my first buil, but is the first buid i want finish, here ( https://www.facebook.com/media/set/?set=a.277548575588597.76498.100000003714419&type=3 ) you can see my other pepakura test
I lied, it isn't my first buil, but is the first buid i want finish, here ( https://www.facebook.com/media/set/?set=a.277548575588597.76498.100000003714419&type=3 ) you can see my other pepakura test
ReveilleWolfie
Jr Member
Your pepakura is very clean, I'm sure you'll finish this one. =]
The Death Angel
Member
thanks.
this afternoon i will post new photos of the helm, with a flew layers of putty
this afternoon i will post new photos of the helm, with a flew layers of putty
The Death Angel
Member
News....
Sad news....
This morning the helm had a little jump from 5 floors, a blow of wind...
But i'm working on it.
Helped by a ultragraphic program (paint Asd) i've made a 3d of the problem, the red lines are the lines where it's broken
I don't just put the primer, i'm waiting to put a flew of putty layer before
Sad news....
This morning the helm had a little jump from 5 floors, a blow of wind...
But i'm working on it.
Helped by a ultragraphic program (paint Asd) i've made a 3d of the problem, the red lines are the lines where it's broken
I don't just put the primer, i'm waiting to put a flew of putty layer before
Now that must've been one hell of a blow of wind ... that, or you said something that angered the heavens !
That's a bad luck, but what minor damage I can see from your masterfully-exectued graphic representation seem very easily repairable. Keep up the good work...and for your armor's sake, watch out for the wind!
That's a bad luck, but what minor damage I can see from your masterfully-exectued graphic representation seem very easily repairable. Keep up the good work...and for your armor's sake, watch out for the wind!
The Death Angel
Member
In my city in winter the wind reaches 120-130 km/h!
Tomorrow i hope i can post new photos, the helmet is fixed
Any one?
Tomorrow i hope i can post new photos, the helmet is fixed
Any one?
- Status
