Fallout New Vegas, NCR Veteran Ranger Armor

Status
Not open for further replies.
i'll cut some stencils and spray paint them, shouldn't be too hard.

as for weathering, i'm going to be experimenting with a few different paints, plastidip is a good thing from what i understand, but i'll be trying a variety of acrylics, enamels, airbrush and inks to see what works best.
 
nothing amazing, quite boring infact.
i've built (but not secured) the nose
as well as working on the eye frames.
things would be quicker if it weren't so cold, otherwise i'd be using my bandsaw to do the cutting, and cut several hours off each nights work.

PA020628.jpg

PA020629.jpg
 

Attachments

  • PA020628.jpg
    PA020628.jpg
    36.9 KB · Views: 285
  • PA020629.jpg
    PA020629.jpg
    63.8 KB · Views: 266
i'll cut some stencils and spray paint them, shouldn't be too hard.

as for weathering, i'm going to be experimenting with a few different paints, plastidip is a good thing from what i understand, but i'll be trying a variety of acrylics, enamels, airbrush and inks to see what works best.

You could go on the foam armoring topic and check out what I did for the weathering. Any questions feel free to ask. Plasti-dip is not used for weathering though, it is only used for coating the foam to seal it up of any cracks or lines that you dont want to show. I am aware that hog mog works just as good too.
 
You could go on the foam armoring topic and check out what I did for the weathering. Any questions feel free to ask. Plasti-dip is not used for weathering though, it is only used for coating the foam to seal it up of any cracks or lines that you dont want to show. I am aware that hog mog works just as good too.

actually i've been under the impression that plastidip makes a great primer for paint to go ontop of..
 
actually i've been under the impression that plastidip makes a great primer for paint to go ontop of..
Both. You use the liquid plasti-dip as a filler/sealer/primer. Since it's the liquid, it's very viscous, allowing it to seal and fill cracks and holes, as well as prime for other paints. Just keep in mind the foam likes to absorb, so more than one coat might be needed...
 
that's good to know, thanks Ron,
i've got a few air bubbles i'm hoping will fill with the primer coat, i guess it might just do that!
 
actually i've been under the impression that plastidip makes a great primer for paint to go ontop of..

Yah, but I was under the impression that you meant you wanted to do battle damage with the plasti-dip, not spraypaint over it, lol! =P You still need to prime over the plasti-dip before you paint though. 1 coat primer, 2 coats paint and 1 coat clear, or vise-vera, 2 coats primer, 1 coat paint and 1 coat clear.
 
nahh, i always prime everything i do,
unless your trying for a very specific "absorbed" look, it's best to prime this stuff, i was just unsure of what to prime it with exactly, until recently.

took part of the mask apart tonight and flared out the edges around the muzzle area,

trying to replicate the flared edges of this picture.
http://www.existentialgamer.com/blog/wp-content/uploads/2010/10/fallout-new-vegas.jpg

than attached the front and lens frames.
PA030631.jpg

PA030630.jpg


now i need a couple of pipes for the gas mask canisters.
 

Attachments

  • PA030630.jpg
    PA030630.jpg
    37.2 KB · Views: 275
  • PA030631.jpg
    PA030631.jpg
    54.4 KB · Views: 255
Your project is coming along nicely! Very creative way of using a combination of materials for your build. :)
 
haven't looked at this in a while and now that I have it is compelling me to move away from pep's and may start on some foamies of my own.
 
Okay folks, big update,
i've been working hard getting the amp on the front of the mask looking right, which isnt easy when its from scratch.
couldn't find a pipe the right diameter to use for it, so i had to improvise.. now i have to do something similar for the gas canister! not going to be fun.
PA060601.jpg

PA060602.jpg

PA060603.jpg

PA060604.jpg

sometime round this period i noticed i was doing it wrong, and had to tear the pieces apart and redo them, so the gap between the sections were even all the way along, rather than kind of arcing outwards.
PA060605.jpg


i felt the mask was too wide, so i cut a slit in the side
PA050599.jpg


and attached it closer.
PA050600.jpg


I also began work with my favorite type of weathering, BATTLE DAMAGE!
so i took my trusty soldering iron to the foam.
PA070606.jpg

PA070607.jpg

PA070608.jpg

PA070609.jpg

PA070610.jpg

PA070611.jpg

PA070613.jpg

PA070614.jpg
 

Attachments

  • PA060603.jpg
    PA060603.jpg
    59.3 KB · Views: 248
  • PA060602.jpg
    PA060602.jpg
    99.7 KB · Views: 237
  • PA060601.jpg
    PA060601.jpg
    52.3 KB · Views: 249
  • PA070609.jpg
    PA070609.jpg
    74.4 KB · Views: 241
  • PA070608.jpg
    PA070608.jpg
    68.9 KB · Views: 354
  • PA070607.jpg
    PA070607.jpg
    82.1 KB · Views: 257
  • PA070606.jpg
    PA070606.jpg
    99.3 KB · Views: 248
  • PA050600.jpg
    PA050600.jpg
    40.1 KB · Views: 226
  • PA050599.jpg
    PA050599.jpg
    41 KB · Views: 246
  • PA060605.jpg
    PA060605.jpg
    46.4 KB · Views: 226
  • PA060604.jpg
    PA060604.jpg
    87.1 KB · Views: 247
  • PA070610.jpg
    PA070610.jpg
    73.7 KB · Views: 246
  • PA070614.jpg
    PA070614.jpg
    31.4 KB · Views: 445
  • PA070611.jpg
    PA070611.jpg
    70.9 KB · Views: 276
  • PA070613.jpg
    PA070613.jpg
    36.7 KB · Views: 302
some people have been curious with how i rigged the straps at the back, so for their benefit.
the silver thing on the strap is a safety pin, i will add a line or two of stitching, once i am satisfied with the entire vest.
PA070615.jpg
 

Attachments

  • PA070615.jpg
    PA070615.jpg
    67.3 KB · Views: 278
I really like your work. You might have already addressed this so if I missed it please forgive me, are you doing the red LEDs in the eyes pieces like the picture in the start screen of new vegas?
 
Status
Not open for further replies.
Back
Top