Recent content by marscreature

  1. marscreature

    3D printed H3 Mk6 armor

    Would you be willing to make a list of the differences? I am only aware of the few obvious ones like the hand and ankle pieces and the visor was just something I happened upon.
  2. marscreature

    3D printed H3 Mk6 armor

    Finally got around to making the top layer of the visor, I have a nice gold visor and was going to just put this clear on top, not sure if I want to paint over it or not so I don't ruin the viability. Top is Acrylic/plexiglass, kinda fragile when bending, the top part snapped off as I was...
  3. marscreature

    3D printed H3 Mk6 armor

    Final layer of Olive paint is on, got some black detail started and will continue that. Next up, print MoeSizzlacs new detail pieces (Thanks for continued updates to your files!). Then work on fitting it together for wear with an undersuit! For an undersuit I am likely going to use some...
  4. marscreature

    3D printed H3 Mk6 armor

    Been busy and it's hard to get time to work on this, also I forget to take more pictures when I do. Wood filler, Sandable Filler Primer, and sanding the Torso, which is the last part before I start putting it together for wearing. Helmet needs work too, want to add a 2nd layer visor for the 3d...
  5. marscreature

    3D printed H3 Mk6 armor

    Thanks, I'll think of something to reinforce it with.
  6. marscreature

    3D printed H3 Mk6 armor

    Chest tape test fits well. I had to cut the bottom middle area a little so I could breathe better, was tight on the sides of my rib cage when inhaling. Going to use sticky back velcro to hold the chest and back pieces together. Also, forgot to print the hand pieces, so those are printed now...
  7. marscreature

    3D printed H3 Mk6 armor

    Finished printing the last chest piece on my Ender 3 Pro and started putting it together. Back piece is a good color contrast example of "welding" pieces together with extra filament and a soldering iron, opposite side taped to hold it in place. All the extremity pieces are 99% done with sanding.
  8. marscreature

    3D printed H3 Mk6 armor

    Back in June bought a 3D printer, had some parts I was obligated to print before Halo parts. All parts needed for my H3 Mk6 armor are printed. Theighs and shins are done, working on the rest now (pictures are from a week ago). May print a helmet since i'm not entirely happy with the cast one I...
  9. marscreature

    Bought a printer and 3D printed all parts needed for H3 Mk6, thighs and shins done...

    Bought a printer and 3D printed all parts needed for H3 Mk6, thighs and shins done, sanding/painting forearms/biceps next, then cod & chest.
  10. marscreature

    Master Chief - Mjolnir - Mark 6 - Halo 3 - 3D printable armor files

    I just bought an Ender 3 Pro to print the armor finally.... MoeSizzlac, how did you get the armor to make it a printable file? (I'm interested in the halo 2 glove piece.)
  11. marscreature

    3D printed H3 Mk6 armor

    Unfortunately haven't progressed at all, still waiting on the prints to be shipped to me... should be here within a week though.
  12. marscreature

    Props Type 32 Rapid Attack Vehicle (AKA Ghost)

    The rolls of paper are 50' so theoretically if needed I could make a print to use it all.
  13. marscreature

    Props Type 32 Rapid Attack Vehicle (AKA Ghost)

    It's nice to have a plotter that can print sheets 48"x50' Printed all my armor pages from it too.
  14. marscreature

    Props Type 32 Rapid Attack Vehicle (AKA Ghost)

    Do you have the Pep files uploaded somewhere? I would appreciate having those.
Top