For Sale Aguilar Workshop Halo 3D Model Collection

J0sephAguilar

New Member
Thought this would be a great place to post about my ODST Helmet, M45 Shotgun, Kukri Knife, ODST Pistol, and Halo 5 Magnum.
All the models are designed for ease of printing/painting/assembly.
Below I will include a basic description and all the links for the article that shows all the features of each model as well as the store page where you can get the models for yourselves







ODST Helmet:
ODST Helmet.png ODST Helmet Assembly.png IMG_4888.jpg
Major Features



Simple Two Piece Design


The helmet itself is comprise of a front and back piece. The back piece doesn't require supports while the front only supports internally meaning that you should have a nice smooth print on the outside. This of course always depends on your print settings, more than likely both pieces will still benefit from supports.



The model also contains two alignment pins that allow for easy alignment and glueing of the pieces together.



Visor Insert Features

The inside of the helmet features Guides to hold the visor in place. While the visor can sit on these alone I would recommend a low strength glue or tape to help fasten hit while still allowing you to remove the visor.



Sizing Ring

Model includes a sizing ring to help you scale the helmet to fit over your head. Sizing ring is a equal to the size of the throat of the helmet so make it so you can fit your whole head through without slicing your ears off.



Full Visor Resin Kit

This model includes a full kit to help you make a rubber mold capable of casting a resin visor. A resin visor in and of itself will have some reflective properties while more importantly allow you to make the visor see-through and a color of your choice. It also allows for more complex geometries than vacuum forming and makes for a sturdier visor. The visor, baseplate, and mold shell all fit together to ensure that the the model only requires a minimal amount of rubber. The less rubber required, the less it costs and the more reusable the mold and easier the demolding process. Model also features a mold stand so that you can ensure the mold can be filled to the top without deformation when you pour in the resin.

Visor Resin Volume: 91.7 mL

Visor Rubber Mold Volume: 391.3 mL



Emile's Knife:
Emile's Knife.png Emile Knife Assembly.png Emile's Knife Prop.jpg
Major Features



Simplistic, Support Free Design


This is a great prop for starters. The only supports required are a minuscule amount on the inside of the handle. The blade slides into the handle and is further stabilized by the connecting rod. As with all of my props, the tolerances allow for secure assembly without sanding or filing.







M45 Shotgun:
M45 Model.png M45 Assembly.png M45 Prop.jpg
Seamless, Modular Design

As you can see this model includes a lot of parts. This was done to minimize the overall supports required (as almost all of the parts can be printed support free) and make the painting and sanding process easier. This also allows this entire piece to have no ugly seams anywhere that they don't naturally lie in actual design.



Working Flashlight Ring Clamps

This piece also includes some flashlight rings that screw together to clamp the placeholder flashlight in place. The place holder flashlight was modeled roughly after a flashlight I found in real life (found in a park so I don't have a link). If like me you want to include a working flashlight in the design. Feel free to try and design your own flashlight rings using the included ones as reference. Or just print some simple rings to make your flashlight fit in the existing ring clamps. Also feel free to message me and I may be able to do you a solid.






ODST Pistol:
M6C SOCOM 2.png M6C SOCOM Assembly 2.png Builds.jpg
Major Features



Sliding Receiver


The back half of the receiver slides back and springs forward just as it does in game. The hooks there can easily support a tensional spring or a small rubber band. The tolerances on the inside of this piece are also slightly larger to allow it to actually slide along the grooves. The front half of the receiver features guiding grooves that make sure that the back half only slides backwards and forwards. Similarly, the root of the slide is angled so that no supports are required to be printed above or around the hook.



Removable Magazine

This design features a removable magazine w/ separate bullet (easier to paint), that can actually be seen in the correct position when the slide is back. The magazine slides in easily but there currently is not mechanism to hold it in place. A little bit of double sided tape or folded tape should easily hold it in place while still allowing it to be removable as opposed to a permanent glue solution. Also if you print multiple you can have them all loaded into your ODST ammo pouches and isn't that just the coolest?



Flashlight Compatibility

The flash light in this pistol includes two pieces, a placeholder flashlight and the flashlight attachment. This is done because the placeholder flashlight is based on a keychain flashlight i found on Amazon small enough to fit into this pistol. The design allows this flashlight to be inserted and activated by just twisting the end as the back of the flashlight is locked in place by the attachment.



Modular, easy to print design

As shown in the assembly picture, this print was sliced in such a way that all seams are hidden along where they would naturally lie, so there is no awkward lines to cover up on the end product. Similarly, minimal support are required, with the only major supports required (depending on your bridging) being on the grip and receiver slide. While the design allows for mix and matching, one should definitely glue the pieces together once you decide as the pegs are not too long and will most likely not support the whole print and are mostly meant for alignment and testing out different configurations. I go into one exception later on in the "Builds" section.





Halo 5 Magnum:
M6H2 Magnum 2.png M6H2 Assembly.png Props.jpg
Major Features



Modular Design


The design of this pistol is such that most of the parts hold themselves in place without the need for glue, this allows for plenty of fun mix and matching. This is of course provided your printer is calibrated correctly. Even so a little glue never hurt once you find your preferred configuration/paint job.



This model makes it so that a majority of the places that require supports end up being hidden upon assembly, so those rough surfaces will be covered. This makes for a much less stressful post print process.



Flashlight Compatibility

The flash light in this pistol includes two pieces, a placeholder flashlight and the flashlight attachment. This is done because the placeholder flashlight is based on a keychain flashlight i found on Amazon small enough to fit into this pistol. The design allows this flashlight to be inserted and activated by just twisting the end as the back of the flashlight is locked in place by the attachment.
 

Attachments

  • M6C SOCOM 1.png
    M6C SOCOM 1.png
    334.2 KB · Views: 18

J0sephAguilar

New Member
ODST SMG


ODST SMG Prop.jpg SMG 2.png SMG Assembly 2.png


Major Features

Threaded Barrel w/ Multiple Barrel Attachments

There is threading on the inside of the Halo 2 Barrel Tip (Compensator?) and the Halo 3: ODST Suppressor. I have tested it out and it screws on easily and securely.



Railing System w/ Multiple Sights

The railing system is functional and the sights slide on and off as you would expect them to. There are also Halo 3: ODST and Halo 2 attachments.



Working Flashlight Compatibility

The flash light in this SMG includes two pieces, a placeholder flashlight and the flashlight attachment. This is done because the placeholder flashlight is based on a keychain flashlight i found on Amazon small enough to fit into this SMG. The design allows this flashlight to be inserted and activated by just twisting the end as the back of the flashlight is locked in place by the attachment.



Seamless Multi-Part Design

All the components slot into each other and will result in no visible seams in the final print. All the parts are already toleranced so that you can print, paint, and assemble with no sanding if you so desire. Also, this allows you to print piece by piece, almost all of which require no supports due to how I designed them. This allows for maximum customization during painting and allows you to not have to back track as far if you mess up a print since most of the parts are on the order of 1-2 hrs depending on your print settings
 

J0sephAguilar

New Member
ODST Arm Armor

Arm Armor Set.png Fore Arm Back.png Fore Arm Front.png Bolt Holes.png Cross Section.png Bicep Plate.png Bolts.png Armor Prop.jpg

Major Features



Bolted, Fitted, Forearm Assembly

The forearm is a two part design that features the main outward armor and one singular in-body plate that can be bolted together with included 3D printable bolt (recommend to print the bolts at 100% infill). The bolts are designed to be compatible with an Alan Key but work just as well just using your fingers.

* ATTENTION*

This model was made by mirroring, this means that while the left forearm bolts use the "righty tighty" method, the left side is opposite.

The inside is modeled to perfectly hug a forearm so that it doesn't slide or twist on the arm and sits right above the wrist. This is only possible with the two piece design as opposed to a singular piece that would require an opening that your hand has to be able to fit through.



Strap Fastener Accommodations

Both the Bicep Plate and the Shoulder Guards were designed to fit strap fasteners to all you to secure the armor to what ever you decided to use as an under layer. Much like the forearms, the shoulder guard is curved to fit a shoulder and the bicep is perfectly fitted to a bicep. For the shoulder straps and bicep straps I used these nylon straps and buckles at 15 mm and 20 mm width respectively.
 

Attachments

  • Shoulder Loops.png
    Shoulder Loops.png
    1,008.7 KB · Views: 14

PerniciousDuke

RCO & BCO
405th Regiment Officer
Hi J0sephAguilar normally files posted on the forum are free to use. You may have noticed our collection of free member-made 3d printable files?



Since you are using the site to advertise your merchandise it may need to be moved to the marketplace section.
 

Cadet

Executive Officer & RCO
Division Staff
405th Regiment Officer
Because these are all links to your Storefront and is intended to advertise your files For Sale, this thread has been moved to the MarketPlace Section.
 
Top