Reply to thread

Message

Documenting my first build and first attempt at any kind of cosplay.
Everything I have made has been 3d printed so far.
I made my helmet with an Ender 3 V2 but then upgraded to a BambuLab P1P.

The files I am using are the Noble 6 file set created by Moesizzlac on Thingiverse.
I split the helmet into 8 pieces in order to fit onto the Ender's print bed.
I superglued the pieces together then finished with some Bondo and a lot of sanding.
The visor is made of thin plastic and one-way window tint.
I made a template out of paper then cut the visor to shape.

I took the up-armor visor attachment from the Armory from here on the 405th:
[URL unfurl="true"]https://www.405th.com/forums/resources/halo-reach-mjolnir-mark-v-accessories.35/[/URL]

I made some tweaks to it in Blender and then scaled it to my helmet.
Both attachments are held in place with magnets.

I will likely make my own vacuum former to create a better visor in the future.

<blockquote data-quote="Barbcelona" data-source="post: 845635" data-attributes="member: 56305">Documenting my first build and first attempt at any kind of cosplay.Everything I have made has been 3d printed so far.I made my helmet with an Ender 3 V2 but then upgraded to a BambuLab P1P.The files I am using are the Noble 6 file set created by Moesizzlac on Thingiverse.I split the helmet into 8 pieces in order to fit onto the Ender&#039;s print bed.I superglued the pieces together then finished with some Bondo and a lot of sanding.The visor is made of thin plastic and one-way window tint.I made a template out of paper then cut the visor to shape.I took the up-armor visor attachment from the Armory from here on the 405th:[URL unfurl=&quot;true&quot;]https://www.405th.com/forums/resources/halo-reach-mjolnir-mark-v-accessories.35/[/URL]I made some tweaks to it in Blender and then scaled it to my helmet.Both attachments are held in place with magnets.I will likely make my own vacuum former to create a better visor in the future.</blockquote>

[QUOTE="Barbcelona, post: 845635, member: 56305"] Documenting my first build and first attempt at any kind of cosplay. Everything I have made has been 3d printed so far. I made my helmet with an Ender 3 V2 but then upgraded to a BambuLab P1P. The files I am using are the Noble 6 file set created by Moesizzlac on Thingiverse. I split the helmet into 8 pieces in order to fit onto the Ender's print bed. I superglued the pieces together then finished with some Bondo and a lot of sanding. The visor is made of thin plastic and one-way window tint. I made a template out of paper then cut the visor to shape. I took the up-armor visor attachment from the Armory from here on the 405th: [URL unfurl="true"]https://www.405th.com/forums/resources/halo-reach-mjolnir-mark-v-accessories.35/[/URL] I made some tweaks to it in Blender and then scaled it to my helmet. Both attachments are held in place with magnets. I will likely make my own vacuum former to create a better visor in the future. [/QUOTE]

This thread is more than 9 months old.

Your message may be considered spam for the following reasons:

This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.

If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

I am aware that replying to this thread may be considered spam, but I still want to make a reply.

Verification