Reply to thread

Message

It’s flexible but not stretchy. Was more a ‘mock up test cut’ for the thigh inserts. I plan to get some foam cut in replacement once I’m happy with the sizing/template itself.

Still trying to figure out if I want to print the back piece or do a foam torso currently, so I’ve traced the whole back Pepakura file into a vector so I can cut it on my machine at work so all the pieces are accurate! So just deciding what route I want to go down with it as i've seen some great foam torso sections, wo this is the section i am still trying to decide how i want to approach going forward.

[ATTACH=full]343058[/ATTACH]

Also started with some sticker templates and printed a few on my printers at work. Went for a reflective vinyl for the upper arm piece. (Test fit/print) so far to see how that would come out!

Starting to wish I had a second 3D printer but carrying on churning out some prints as much as I can.

[ATTACH=full]343045[/ATTACH] [ATTACH=full]343046[/ATTACH]

[ATTACH=full]343047[/ATTACH] [ATTACH=full]343049[/ATTACH]

<blockquote data-quote="IMP3RIOUS" data-source="post: 839076" data-attributes="member: 47580">It’s flexible but not stretchy. Was more a ‘mock up test cut’ for the thigh inserts. I plan to get some foam cut in replacement once I’m happy with the sizing/template itself.Still trying to figure out if I want to print the back piece or do a foam torso currently, so I’ve traced the whole back Pepakura file into a vector so I can cut it on my machine at work so all the pieces are accurate! So just deciding what route I want to go down with it as i&#039;ve seen some great foam torso sections, wo this is the section i am still trying to decide how i want to approach going forward.&nbsp; &nbsp; &nbsp; &nbsp; [ATTACH=full]343058[/ATTACH]Also started with some sticker templates and printed a few on my printers at work. Went for a reflective vinyl for the upper arm piece. (Test fit/print) so far to see how that would come out!Starting to wish I had a second 3D printer but carrying on churning out some prints as much as I can.[ATTACH=full]343045[/ATTACH]&nbsp; &nbsp; [ATTACH=full]343046[/ATTACH][ATTACH=full]343047[/ATTACH]&nbsp; &nbsp;&nbsp; [ATTACH=full]343049[/ATTACH]</blockquote>

[QUOTE="IMP3RIOUS, post: 839076, member: 47580"] It’s flexible but not stretchy. Was more a ‘mock up test cut’ for the thigh inserts. I plan to get some foam cut in replacement once I’m happy with the sizing/template itself. Still trying to figure out if I want to print the back piece or do a foam torso currently, so I’ve traced the whole back Pepakura file into a vector so I can cut it on my machine at work so all the pieces are accurate! So just deciding what route I want to go down with it as i've seen some great foam torso sections, wo this is the section i am still trying to decide how i want to approach going forward. [ATTACH type="full" width="843px"]343058[/ATTACH] Also started with some sticker templates and printed a few on my printers at work. Went for a reflective vinyl for the upper arm piece. (Test fit/print) so far to see how that would come out! Starting to wish I had a second 3D printer but carrying on churning out some prints as much as I can. [ATTACH type="full" width="438px" alt="IMG_0846.jpeg"]343045[/ATTACH] [ATTACH type="full" width="361px" height="983px"]343046[/ATTACH] [ATTACH type="full" width="398px" alt="IMG_0848.jpeg"]343047[/ATTACH] [ATTACH type="full" width="398px" alt="IMG_0856.jpeg"]343049[/ATTACH] [/QUOTE]

This thread is more than 11 months old.

Your message may be considered spam for the following reasons:

This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.

If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

I am aware that replying to this thread may be considered spam, but I still want to make a reply.

Verification