PA Cosplay

New Member
I've been working on this for a few weeks now so I thought I'd share my progress. Im making an OFST armor set but going for a legend of zelda paint style, ill also be making the master sword and shield for my weapons. I might make a small gun as well but don't know if ill have enough time for now. So far I have the shoulders, forearms, and shins printed. Next up are the thighs but the file doesn't fit my printer. Going to figure that out next as I work on the sword.
 

Attachments

  • 20210404_175224.jpg
    20210404_175224.jpg
    1.8 MB · Views: 33
  • 20210412_120459.jpg
    20210412_120459.jpg
    1.3 MB · Views: 31
  • 20210420_112953.jpg
    20210420_112953.jpg
    1.4 MB · Views: 29
  • 20210420_113009.jpg
    20210420_113009.jpg
    1.6 MB · Views: 31

Benton188

RXO
405th Regiment Officer
Member DIN
S188
Ahhh yeah. I am a Stan for cross-over armor builds. Will you be making the traditional sword and shield or a mash-up version of those as well?
 

Bucky

New Member
What files did you use for the forearms? The files I have are Moe's and there are cutouts for the elbow... I'd like the ones you have ahah
 

PA Cosplay

New Member
Had to slice up the thigh pieces twice to make them eaiser for me to print. 36 hours later im 1/4 of the way through each so far.
 

Attachments

  • 20210427_094512.jpg
    20210427_094512.jpg
    1.4 MB · Views: 9
  • 20210427_094514.jpg
    20210427_094514.jpg
    1.5 MB · Views: 8
  • 20210427_094514.jpg
    20210427_094514.jpg
    1.5 MB · Views: 8
  • 20210427_093659.jpg
    20210427_093659.jpg
    1.2 MB · Views: 9
  • 20210427_093714.jpg
    20210427_093714.jpg
    606.5 KB · Views: 10

PA Cosplay

New Member
What files did you use for the forearms? The files I have are Moe's and there are cutouts for the elbow... I'd like the ones you have ahah
I'll have to take a look, if I remember right I got them off of moe as well. If I can't find them ill see if I can send it to ya or post it on here.
 

PA Cosplay

New Member
Outer shells done and done! Last piece finished last night. Trying out "welding" insted of gluing this time. It ain't pretty but so far its alot stronger than when I glued them. Going to finish up attaching the new parts while the inner thigh parts print.
 

Attachments

  • 20210430_093550.jpg
    20210430_093550.jpg
    1.2 MB · Views: 10
  • 20210430_093536.jpg
    20210430_093536.jpg
    1.1 MB · Views: 10
  • 20210430_093524.jpg
    20210430_093524.jpg
    1.1 MB · Views: 8
  • 20210430_093507.jpg
    20210430_093507.jpg
    1.2 MB · Views: 9

PA Cosplay

New Member
Got everything else welded and started filling the gaps. The inner thigh pieces were rough, tried using up a few partial rolls but I couldn't figure out how to hot-swap the rolls so I tried somthing different. I ran the roll out, figured out how much was left to print, sunk the model down in cura and hit print! Sad I can't get hot-swapping figured out but atleast im not wasting what I got printed anymore.
 

Attachments

  • 20210505_200039.jpg
    20210505_200039.jpg
    2.4 MB · Views: 9
  • 20210505_200049.jpg
    20210505_200049.jpg
    2.1 MB · Views: 9
  • IMG_20210505_200734_454.jpg
    IMG_20210505_200734_454.jpg
    184 KB · Views: 8
  • 20210505_121504.jpg
    20210505_121504.jpg
    1.8 MB · Views: 7
  • 20210505_163829.jpg
    20210505_163829.jpg
    2.6 MB · Views: 8
  • 20210505_164014.jpg
    20210505_164014.jpg
    2.6 MB · Views: 8

Your message may be considered spam for the following reasons:

  1. Your new thread title is very short, and likely is unhelpful.
  2. Your reply is very short and likely does not add anything to the thread.
  3. Your reply is very long and likely does not add anything to the thread.
  4. It is very likely that it does not need any further discussion and thus bumping it serves no purpose.
  5. Your message is mostly quotes or spoilers.
  6. Your reply has occurred very quickly after a previous reply and likely does not add anything to the thread.
  7. This thread is locked.
Top