My Finished Hello Kitty x Halo Spartan Suit

Bowye

Member
Member DIN
S147
Hello all! My name is Bowye, and I'm really new to cosplay and the community. As stated this will be my first Halo spartan suit (mostly 3d printed). But this isn't some normal ol spartan, it's going to be themed after the character Hello Kitty! It will be known as the Halo Kitty (hehe). Here is how it should look like! Since this is my first Halo Spartan suit I am listening for comments and help! Thanks guys!
20220705_191628.jpg
 
Last edited:
I've already started to work on the helmet. I got the files from Galatic Armory.
It took about 3 days to print out in pla.
20220423_110813.jpg


Went with Bondo Glazing and Spot putty for the whole helmet
20220423_181109.jpg

20220423_110813.jpg

Sand then Filler Primer, you get the drill

20220423_191301.jpg


Fast foward to the paint, but no weathering yet.
And don't worry for the crappy bow! It's only temporary.
20220424_202517.jpg


And for the final touches on the helmet are the visor (that I might change), some weathering, and the wiskers.
20220714_001114.jpg


Overall it was a fun helmet to build! I might redo the weathering since I think went a little overboard.
 
I have the left and right shoulders, one forearm, and the groin printed out and being sanded. I am starting to attach them.
20220728_120146.jpg
20220728_120151.jpg

I have a question/concern, I do not like the fact that there is a big gap at my shoulder. How can I make it look better? I was thinking of a shoulder pad I could buy, but I want some advice first.

210220728_120146.jpg
 
I have the left and right shoulders, one forearm, and the groin printed out and being sanded. I am starting to attach them.
View attachment 321238View attachment 321239
I have a question/concern, I do not like the fact that there is a big gap at my shoulder. How can I make it look better? I was thinking of a shoulder pad I could buy, but I want some advice first.

View attachment 321242
I am planning on making a rubber seal that will fit around the inside of the chest. I'm hoping it will come out similar to the in game model similar to the attached picture.
 

Attachments

  • 20220520_103642.jpg
    20220520_103642.jpg
    2 MB · Views: 74
  • 20220520_103652.jpg
    20220520_103652.jpg
    2.1 MB · Views: 73
Absolutely loving it! As for the chest and shoulders, if you want a rubber undersuit/seal thing I believe Nerdforge includes those in the files he made, otherwise I’m sure we’ve got resources for foam ones somewhere in the community!
 
Absolutely loving it! As for the chest and shoulders, if you want a rubber undersuit/seal thing I believe Nerdforge includes those in the files he made, otherwise I’m sure we’ve got resources for foam ones somewhere in the community!
Agreed! looking fantastic so far! I love the kitbash! As for the "wings" or gasket, Nerdforge does indeed include files for it, but I think it's meant to be a template or mold for casting it in rubber. If you do figure out how to make it into a wearable piece however, let me know! That and the chest gasket are the last pieces I need to figure out for my build!
 
Hello again! I have about 90 percent of the armor built! Really REALLY sloppy tho. Im planning on going to Silicon 2022, so i really have to cut some corners. But I am very excited on how it is going! All that is left is the shoes and shins ( and maybe a gun if i have the time). What gun would go good with this suit?
VideoCapture_20220815-171459.jpg
 
This thread is more than 7 months old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top