Strapping Guide: Making, and sizing it.

Status
Not open for further replies.

Ashuraa

Research Team Lead
Member DIN
S015
SO, I have had a few people asking about strapping recently.

After making several suits for my husband @Kusak , I have learned a few things on what has worked for us.

So, when @Lobbster contacted me to help him make his strapping I jumped on it. Our plan is to place the strapping inside his black suiting. Only where the buckles need to be out will there be keyholes, or buttonholes for the strapping to come through his suiting.

So. FIrst step was to have him put on his black undersuit, and his armor on.
IMG_20201023_190744854.jpg

This let me figure out where the edges of his armor was going to be, and where I wanted the strapping to show.
IMG_20201023_191132893.jpg

I marked the edges with Tailors chalk, and saftey pins.
IMG_20201023_192236133.jpg

I marked where I wanted the strapping to end for each section.

Then I had him remove his armor.

The next step was to measure his waist, about the place that he wears his normal belts.

From there I measured from his waist, over his shoulders, and to the opposite side of his back, creating a cross point in the middle of his back.
IMG_20201023_193158115.jpg

The next measurements were from the front of his waist down to the top of his thigh pieces, then to the top of his shins.
Repeat that for the back of his legs.

This gave me all the measurements I needed.

Our materials list was,
1 inch web strapping
1 inch elastic
1 inch parachute buckles
1 inch tri glide, strap adjusters
2mm foam
IMG_20201023_193858713.jpg



So. The pattern design is a solid belt, with suspenders, and leg suspension rigs. We also have attachment points coming off of the shoulders.
20201023_215812.jpg


20201023_215822.jpg

I added tri glides, and extra webbing to give us a good bit of adjust-ability.


Now, at the shoulders, we added a strap of elastic from the front to the strap to help keep the armor from twisting. It would also give, giving Lobb his movement while pulling the armor piece back into place.


We added a strap across his upper chest to help keep the shoulder straps from sliding outwards.

Next, we did his leg straps.
IMG_20201024_160430571.jpg

We had 4 straps total here.

2 front
and 2 back


We made then double layered. The hip to thigh strap which was 1 inch web. The second layer was 1 inch elastic down to the top of the shin.
IMG_20201024_162459211.jpg


IMG_20201024_162504348.jpg


IMG_20201024_162509543.jpg


IMG_20201024_162535364.jpg


On each of these we have adjustable tri glides, and buckles.


Once we had the base built we then needed to connect the buckles to the armor pieces.


One of the best ways I have found out to do this was to make a strapping sandwich.

What this means is taking your elastic to the buckle, and then sewing it to a piece of foam.
IMG_20201024_152623043_HDR.jpg


IMG_20201024_155617356.jpg


We then had Lobb rearmor. We did his legs first.

Once he started to put his armor on, I was able to figure out where the buckles needed attached inside the armor.

Use contact cement on the small foam squares, and glue it to the armor.
IMG_20201024_155617356.jpg

Let that dry, and then we kept building his armor upwards.

Soon we had the full strapping done. Next will be to make my keyholes, and
20201024_173011.jpg
put the strapping inside his undersuit.



20201024_173035.jpg


IMG_20201024_181035278.jpg


IMG_20201024_181044760.jpg


IMG_20201024_181100279.jpg



P.s. As soon as I get the suit again, I will be making the keyholes. I will update the above post with how those are added, and how it looks with the straps fully hidden.
 

Attachments

  • IMG_20201119_211400094.jpg
    IMG_20201119_211400094.jpg
    2.3 MB · Views: 325
  • IMG_20201119_211418208.jpg
    IMG_20201119_211418208.jpg
    4 MB · Views: 265
  • IMG_20201119_211505098.jpg
    IMG_20201119_211505098.jpg
    3.9 MB · Views: 263
  • IMG_20201119_211809241.jpg
    IMG_20201119_211809241.jpg
    3.7 MB · Views: 251
  • IMG_20201119_211814023.jpg
    IMG_20201119_211814023.jpg
    2.7 MB · Views: 252
  • IMG_20201119_212619960.jpg
    IMG_20201119_212619960.jpg
    2.2 MB · Views: 265
  • IMG_20201119_212626203.jpg
    IMG_20201119_212626203.jpg
    2.8 MB · Views: 263
  • IMG_20201119_212628993.jpg
    IMG_20201119_212628993.jpg
    2.3 MB · Views: 262
  • IMG_20201119_213921534.jpg
    IMG_20201119_213921534.jpg
    2.4 MB · Views: 260
  • IMG_20201119_213925131.jpg
    IMG_20201119_213925131.jpg
    3.8 MB · Views: 259
  • IMG_20201119_214504581.jpg
    IMG_20201119_214504581.jpg
    2.5 MB · Views: 255
  • IMG_20201119_214631797.jpg
    IMG_20201119_214631797.jpg
    2.7 MB · Views: 254
  • IMG_20201119_214805857.jpg
    IMG_20201119_214805857.jpg
    2.9 MB · Views: 261
  • IMG_20201119_214809854.jpg
    IMG_20201119_214809854.jpg
    1.9 MB · Views: 264
  • received_190233082644462.jpeg
    received_190233082644462.jpeg
    542.8 KB · Views: 283
Last edited:
this is the same way i do my storm trooper outfit i was wondering if i could do this armor the same way as MrJamin said it is really clear for those of us who have no done the strapping for these armors

thank you so much
 
That's an amazing system Ashuraa! I can't begin to imagine how much more comfortable and reliable that'd be than just velco, for example. No more looking back every ten seconds to see if something fell off...
 
Hey Ashuraa this is a great walkthrough on a topic we don't have much info on. I missed it because I only search titles with tutorial or guide in them. Can you change your title to include one of those words?

Perhaps, Straping Guide: Making and sizing it
 
I have a surplus store near me that has the web strapping for cheap. And they have buckles often too.

Other places I find them at is Joanne's.

And amazon.
Where did you purchase the buckles and straps from? Been trying to find a good shop.
 
Status
Not open for further replies.
Back
Top