1st Build Halo 3 MKVI build

[SgtSaint]

Amazon.com: RIYA Waist Trimmer Sweat Waist Trainer for Women and Men Waist Sweat Belt Band Belly Stomach Wrap Black : Sports & Outdoors used as an ab wrap. for a more uniform look with out an actual foam ab wrap. (this can get hot)

As mentioned regarding the wet suit heat building up going to be detrimental: I would expect that buying something DELIBERATELY DESIGNED to make you sweat is going to be a horrible idea.

 

[billeybob250]

As mentioned regarding the wet suit heat building up going to be detrimental: I would expect that buying something DELIBERATELY DESIGNED to make you sweat is going to be a horrible idea.

Hah. I had not noticed that. The wife bought it for me.

You got a better buyable ab wrap?

 

[Zackurai]

Good Ol’ Etsy might will have a undersuit thingy for ya, or maybe some breathable motorcycle padded shirt too

 

[Cadet]

I have to agree with Clint, I'm not sure a "Sweat Waist Trainer" is the best option. I would be concerned about heat retention during summer months, also, it is looks to just be sort of plain black with no additional details or accents?
There are other Compression and Sports gear shirts on Amazon that have padded sections or seam line and segments that will add a little detail or pop, even if they aren't accurate to the Halo 3 Details, more so than a plain black wrap. Here is an example:

Amazon.com

As for strapping and Harness systems, NobleOfDeath recently finished writing up an excellent tutorial on the Universal/Modifiable harness system he has developed over the years and across multiple sets of armor:

Universal Harness System for Armored Cosplay (TUTORIAL)

INTRODUCTION: The Challenge The timeless challenge that all armored cosplayers face once their stunning pieces are complete is figuring out how to put them on effectively. There are so many different sections to manage, and plenty of things to watch out for—like rotating biceps, stuff sitting...

www.405th.com

 

[SgtSaint]

Hah. I had not noticed that. The wife bought it for me.

You got a better buyable ab wrap?

Spartan under suit — Starbase3d

All Laser engraved treads & patterns, faux connectors, greeblies, rivets and so forth have been painstakingly recreated from the TV series, in-house and are exclusive to Starbase3d. Abdominal panels Stage 1 consists of the panels for the abdominal region. The span exposed below the che

www.starbase3d.com

 

[Womanrepelnt]

Gentlemen I have another update. After some more sanding and dealing with putty ive deiced to use UV cured resin in plane of bondo for smaller imperfections, what this means is that I'm gonna slap resin onto a already primed print in a hail marry to fill all the little tiny gaps and get the smooth finish before doing one last wet sand before final coat of filler primer. However on the better news after sine serious work the forearms are fully finished and the parts for a basic rigging kit are on the way!

PS I want to gibe a shoutout to all of your guys help its really appreciated!

 

[billeybob250]

Looking good so far.

 

[Womanrepelnt]

After some insperation from the Unviseral harness syetem and other designs I saw across the internet I present to you the MCS (Modular Connection System)! If you have any ideas on how to improve please leave your ideas in the comments!

 

[billeybob250]

I also have snaps that go from my thighs to my shins. But that is almost exactly how my rigging is.

 

[Womanrepelnt]

I also have snaps that go from my thighs to my shins. But that is almost exactly how my rigging is.

Was it from your thigh piece to your shin? or did you extend the line to go lower?

 

[billeybob250]

Bottom of my thick to my shin, on the outside and inside of my knee.

I also have no padding in my shins so I have to hold them up.

 

[Womanrepelnt]

Bottom of my thick to my shin, on the outside and inside of my knee.

I also have no padding in my shins so I have to hold them up.

could you send an image?

 

[billeybob250]

The strap are on either side of my knee and are button push from the inside for easy access. I wouldnrecomend sewing the nylon loops if you know how to. I did not.

 

[Womanrepelnt]

The strap are on either side of my knee and are button push from the inside for easy access. I wouldnrecomend sewing the nylon loops if you know how to. I did not.

lmao, and your just going no foam?! Does that not just clang around?

 

[billeybob250]

lmao, and your just going no foam?! Does that not just clang around?

hey i never said i wasn't loud. i cant see where im going nor can i move much. you need to be able to hear that I'm coming and you can get outta my way.

 

[rickrtickr]

After some insperation from the Unviseral harness syetem and other designs I saw across the internet I present to you the MCS (Modular Connection System)! If you have any ideas on how to improve please leave your ideas in the comments!

You have a pretty common setup there.

This may not have much impact on your plans, but I would make one note.

The single-point attachment of the Thighs has given me a world of better mobility than the older two-point attachment.

I would also note that my entire lower suit is foam for comfort, and as such, my shins can rest directly on the boots without needing any other supports. And the Thighs just need the one point to clip onto my harness:

It looks like you are pretty well on your way to getting the process sorted. And as you noted to Bob. A foam (even if only a 1-3mm Eva craft foam) barrier to parts that may rub or bump into each other with any frequency can help with clicking and clacking as you move about. (foam has a tendency to squeak at times, though if the rub is constant enough.) Not to mention the use of various upholstery foams to maintain fit and positioning while wearing the armor.

 

[Womanrepelnt]

You have a pretty common setup there.

This may not have much impact on your plans, but I would make one note.

The single-point attachment of the Thighs has given me a world of better mobility than the older two-point attachment.

I would also note that my entire lower suit is foam for comfort, and as such, my shins can rest directly on the boots without needing any other supports. And the Thighs just need the one point to clip onto my harness:
View attachment 372034

It looks like you are pretty well on your way to getting the process sorted. And as you noted to Bob. A foam (even if only a 1-3mm Eva craft foam) barrier to parts that may rub or bump into each other with any frequency can help with clicking and clacking as you move about. (foam has a tendency to squeak at times, though if the rub is constant enough.) Not to mention the use of various upholstery foams to maintain fit and positioning while wearing the armor.

how exactly did you get the shins to rest on the boots? I presume you used EVA foam, no? and for the single point attachement ill keep it in mind as I fully intend to wear my armor at my local convention that requires a lot of walking.

 

[Womanrepelnt]

how exactly did you get the shins to rest on the boots? I presume you used EVA foam, no? and for the single point attachement ill keep it in mind as I fully intend to wear my armor at my local convention that requires a lot of walking.

as well as the shoes themself, did you print a cover on them so you can wear them out of cosplay or was it a sacrifical pair of shoes?

 

[rickrtickr]

as well as the shoes themself, did you print a cover on them so you can wear them out of cosplay or was it a sacrifical pair of shoes?

For the shins, it is all down to scale and gravity. Since they are completely foam, they fit snugly and just "fall" down until they are in direct contact with my boots.

As for my boots themselves, they are also made of foam, but they have a "Core" that uses a cheap pair of shoes from Walmart and a wooden sole to act as a lifting platform to add some extra height. (the shoes are screwed and Glued to the wood so that they don't wiggle while I am wearing them.) In theory, you could follow a similar method to print the boot Cap and use the same practice.

 

[Womanrepelnt]

For the shins, it is all down to scale and gravity. Since they are completely foam, they fit snugly and just "fall" down until they are in direct contact with my boots.

As for my boots themselves, they are also made of foam, but they have a "Core" that uses a cheap pair of shoes from Walmart and a wooden sole to act as a lifting platform to add some extra height. (the shoes are screwed and Glued to the wood so that they don't wiggle while I am wearing them.) In theory, you could follow a similar method to print the boot Cap and use the same practice.

View attachment 372037View attachment 372036

Ohhhhh, thats pretty smart. But im hoping to fully 3D print everthing so I may have to fill it with foam and pray gravity and the foam inside does its job.