Foam SPI Head Hunter

TillXValhalla

Active Member
This is the start of my SPI S-III head hunter build. I intend to use the CQC helmet and the ODST marksman shoulder to "customize" into a headhunter. I will eventually make an SPI helmet as well and the MA5k to be an average SPI S-III as a varient but the initial build will be for a head hunter. the sizing isnt 100% accurate in the armorsmith pics but just for proof of concept. hopefully i finish this one unlike my pile of shame over int the corner.
 

Attachments

  • front-2.jpeg
    front-2.jpeg
    114.1 KB · Views: 186
  • side.jpeg
    side.jpeg
    117.8 KB · Views: 182
  • front.jpeg
    front.jpeg
    113.1 KB · Views: 177
  • SPI.jpeg
    SPI.jpeg
    1.2 MB · Views: 198
The CQC and Sharpshooter UA are some interesting additions. Are you going to add any soft parts like pouches on over the main shell anywhere?
 
The CQC and Sharpshooter UA are some interesting additions. Are you going to add any soft parts like pouches on over the main shell anywhere?
I'll probably add the reach thigh soft case (need to hold my wallet and phone as such). As for magazines pouches and such I haven't fully decided yet. Being able to reload the sniper would be cool at a con. You have any advice for the headhunter build?
 
After a very long hiatus were back at it again. On the first day I've got both feet and 1 shin done. Being the old school concept of the SPI leaves a bit that needs to be free handed or adjusted a bit, this is all I have to show after 7 hours of some trial and error. Hoping to get all the way to the thighs this weekend.
 

Attachments

  • 20230916_191804.jpg
    20230916_191804.jpg
    1.3 MB · Views: 65
  • 20230916_191708.jpg
    20230916_191708.jpg
    1.5 MB · Views: 64
  • 20230916_131635.jpg
    20230916_131635.jpg
    1.5 MB · Views: 60
  • 20230916_131606.jpg
    20230916_131606.jpg
    1.5 MB · Views: 60
Update Saturday addition. The chest is done. Only took 17ish hours for it it to be to small by half an inch so I don't have the 2nd tummy tier. But will adjust something later. And way down the road I will make another one. But for now and possibly for the Con on a mannequin the chest is fabricated. The shoulder "straps" are gonna need so much foam clay.
 

Attachments

  • 20231021_220749.jpg
    20231021_220749.jpg
    1.8 MB · Views: 57
  • 20231021_220901.jpg
    20231021_220901.jpg
    1 MB · Views: 51
  • 20231021_220848.jpg
    20231021_220848.jpg
    1.3 MB · Views: 53
Been a little while for an update with all the holiday shenanigans. But I got a new printer and wanted to test it out so now the shoulders are printed. Just have to sand the poly effect. The forearms will still be foamed. Just have to fabricate the forearms, detail, do all the seam work, and print the helmet. Almost done.
 

Attachments

  • 20231212_171021.jpg
    20231212_171021.jpg
    1.3 MB · Views: 35
  • 20231212_171027.jpg
    20231212_171027.jpg
    1.1 MB · Views: 33
  • 20231213_081416.jpg
    20231213_081416.jpg
    1.2 MB · Views: 34
This thread is more than 4 months old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top