BiGHARYSCOTSMiN
Member
52 pages and growing... dayum Crim!
File it under Crimmson
- Thread starter Crimmson
- Start date
- Status
Crimmson
Well-Known Member
I know right.
hope to see it finished. post a pic here if you want.
h4 recon edited, remodeled, unfolded-Crimmson
measurement
the highlighted areas are not needed, but I like it.
remember to take into account the, maybe, 1/4 inch gap in between the front plate and back plate that I left to make it easier to unfold.
the scale is h-440, w-350, d-406 and scale is 20.10, 212 point to point measurement in pep equal roughly 8 inches deep plus the 1/4 inch to 1/2 gap,37 pages. I really don't know why I picked those numbers as I dont have much experience unfolding. if you do edit the unfold remember that I enclosed the armor on the inside adding extra pages to the unfold, if you want move the flaps to the extra pieces away from the regular armor pieces in case you don't want to use them. doing this will also subtract from the total pages by probably 4 or 5 pages(see above pic).
remember to give yourself credit if you edit the unfold and please re upload it, don't hoard it.
link
http://www.mediafire.com/download/58ad38mkd5dq9ul/h4_recon_chest_remodel_and_unfold-Crimmson.pdo
can some one look this over and see if it is good to go, I don't do much unfolding so.... yeah. enjoy.
copyright Microsoft, 343 non profit use only
NoMaybeYes
Member
I can look it over in a few hours and get back to you. It does looks fairly organized and well done though.
Will do so I just finished pepping the eye I am taking my time want to make it look excellent and excellent work with the above piece of armor if you ever have time I think you will do deathstroke justice I know you have a lot of requests just hoping one day that you will model it 
NoMaybeYes
Member
This is a Very good unfold Crimmson. Everything is organised so you dont have everything scattered. The only thing you could have done was decrease the Threshold to about 160 or 165. Doing so takes care of all the unneeded folding lines. If you're curious about what I mean look in Settings-->Other Settings --> and its the very bottom option. Rhinoc gave me some tips back when the Halo 4 asset pack came out and its helped a lot. Post #25 is where he talks about it and some others in my unfolding stuff if you want to look further into it.
Crimmson
Well-Known Member
yeah my fingers hurt a lot from cutting as well.
thank you.
maybe I should have put this up before, but this is what I am aiming for, for my build of course. I plan on unfolding everything before I start building to make sure I have the files I want,plus you guys benefit from this as well.
protector helmet- edited and unfolded
recon chest- edited and unfolded
venator shoulders- edited and unfolded
twin plated arms- edited and unfolded
xg89 narrow butt plate-edited and unfolded
xg89 narrow thigh plate- edited and unfolded
xg89 narrow shin plates- edited and unfolded
xg89 narrow boot- edited and unfolded
and I have no time line to follow. tell what you guys and gals think of this set up.
here is the protector helmet. edited, mesh welded, but I kept the skill level low as I plan to details with the foamies. hhhmmmm foamies. (I don't know why this sounds like something you eat and enjoy)
link
http://www.mediafire.com/download/5pqj4z8frqwx57l/H4_PROTECTOR_HELMET.pdo
recon chest
link
http://www.mediafire.com/download/58...d-Crimmson.pdo
venator shoulder, same as above, edited mesh welded, but I kept the skill level low, etc
link
http://www.mediafire.com/download/62zo9r6rr4mah95/H4_VENATOR_SHOULDER.pdo
also can some one look these over to make sure the unfolds are good to go. thanks
copyright Microsoft, 343. non profit only
Crimmson
Well-Known Member
alright here is the twin plated arm, edited minus some parts I felt were unneeded.
http://www.mediafire.com/download/t6jc22sf0ppdq2d/H4_TWIN_PLATED_ARMS.pdo
copyright Microsoft, 343, non profit only.
http://www.mediafire.com/download/t6jc22sf0ppdq2d/H4_TWIN_PLATED_ARMS.pdo
copyright Microsoft, 343, non profit only.
Crimmson
Well-Known Member
here is the xg89 butt plate, thigh and boot. you guys know the deal. I will work on the shins later. also I plan on leaving the shin in the four major parts, apart, build them and then use an elastic band to attach them together.
link
http://www.mediafire.com/download/noihravujv3bn03/H4_XG89_NARROW_thigh.pdo
link
http://www.mediafire.com/download/b7exxbs7n55c4qa/H4_XG89_NARROW_boot.pdo
link
http://www.mediafire.com/download/fnacuqacc91pi2f/H4_XG89_NARROW_butt_plate.pdo
please check them out for me guys thanks.
copyright Microsoft, 343, nonprofit only
link
http://www.mediafire.com/download/noihravujv3bn03/H4_XG89_NARROW_thigh.pdo
link
http://www.mediafire.com/download/b7exxbs7n55c4qa/H4_XG89_NARROW_boot.pdo
link
http://www.mediafire.com/download/fnacuqacc91pi2f/H4_XG89_NARROW_butt_plate.pdo
please check them out for me guys thanks.
copyright Microsoft, 343, nonprofit only
Crimmson
Well-Known Member
xg89 narrow shin plates
link
http://www.mediafire.com/download/571942seuerrt26/H4_XG89_NARROW_shin.pdo
and now to procrastinate, print stuff out, procrastinate some more, motivate myself to build it, procrastinate, slowly build it. yeah that sounds about right.
copyright Microsoft, 343, non profit
link
http://www.mediafire.com/download/571942seuerrt26/H4_XG89_NARROW_shin.pdo
and now to procrastinate, print stuff out, procrastinate some more, motivate myself to build it, procrastinate, slowly build it. yeah that sounds about right.
copyright Microsoft, 343, non profit
Crimmson
Well-Known Member
how can I help you with the mk vi?
ok so I keep changing my mind on the some of the armor, well the forearms any ways. reason being that the armor is already in multiple pieces, hence it would be easier to slip on. of course with the help of elastic to strap it together.
link
http://www.mediafire.com/download/61b2l1lfjllt62x/h4_contoured_arm.pdo
copyright Microsoft, 343 non profit only.
edit: had to upload new file as the old had overlapping issues, did not update the pic though
Chernobyl
Sr Member
More in the way of helping me with the torso than anything - I'm trying to prep the files for my eventual H4 build and I'm going to be using Mk VI for most of it.
Crimmson
Well-Known Member
how do you want the h4 mk 6 torso: one solid piece, two pieces(front plate, back plate with 'boosters' mesh welded) or three pieces(front plate, back plate, booster packs) that worked out weird.
numerically.
Crimmson
Well-Known Member
I have not started on them yet. I have only started on the mk6 g2 chest and that might take abit as my work load is pretty hectic at the moment. 16 hr days minimum, doesnt leave much room for much
tac2002
Active Member
no worries cimmson just thought id ask...never hurts to ask and sorry to bother, but lets just say you do awesome work and i hope you get a chance to take a breather keep up the awesome work!:cool
- Status
