CWayte

New Member
New poster here, I got a Creality CR10 Smart Pro for Christmas, been printing plant stuff for the missus and some oversized floating Benchys for the kids, finally time to print something for me

Decided to buy the M6C Socom files from Galactic Armory and give it a go, here’s the work in progress up until now, still got to sand and finish printing the laser module. Tried to glue magnets into the magazine so it remained removable but held in place, accidentally put it in too early even though the glue felt dry and now it’s stuck, but such is learning.

Also had to pause the print remotely and fix a broken support, but impressed it still turned out salvageable, but I refused to waste 17/22 hours of printing.
 

Attachments

  • IMG_4052.jpeg
    IMG_4052.jpeg
    1.2 MB · Views: 78
  • IMG_4053.jpeg
    IMG_4053.jpeg
    1.2 MB · Views: 66
  • IMG_4054.jpeg
    IMG_4054.jpeg
    1.2 MB · Views: 85
  • IMG_4055.jpeg
    IMG_4055.jpeg
    1.5 MB · Views: 79
  • IMG_4056.jpeg
    IMG_4056.jpeg
    1.3 MB · Views: 84
  • IMG_4057.jpeg
    IMG_4057.jpeg
    1.2 MB · Views: 56
  • IMG_4067.png
    IMG_4067.png
    2.6 MB · Views: 62
  • IMG_4072.png
    IMG_4072.png
    3.2 MB · Views: 66
  • IMG_4074.png
    IMG_4074.png
    3.7 MB · Views: 67
  • IMG_1920.jpeg
    IMG_1920.jpeg
    1.7 MB · Views: 64
  • IMG_4089.jpeg
    IMG_4089.jpeg
    1.6 MB · Views: 71
  • IMG_4090.jpeg
    IMG_4090.jpeg
    1.6 MB · Views: 66
  • IMG_4091.jpeg
    IMG_4091.jpeg
    568.8 KB · Views: 69
  • IMG_4092.jpeg
    IMG_4092.jpeg
    575.5 KB · Views: 78
  • IMG_4093.jpeg
    IMG_4093.jpeg
    2.3 MB · Views: 67
  • IMG_4099.jpeg
    IMG_4099.jpeg
    2.3 MB · Views: 76
  • IMG_4103.jpeg
    IMG_4103.jpeg
    1.1 MB · Views: 62
  • IMG_4106.jpeg
    IMG_4106.jpeg
    1.8 MB · Views: 82
  • IMG_4111.png
    IMG_4111.png
    2.5 MB · Views: 74
  • IMG_4125.jpeg
    IMG_4125.jpeg
    251.3 KB · Views: 69
  • IMG_4126.jpeg
    IMG_4126.jpeg
    240.9 KB · Views: 72
  • IMG_4128.jpeg
    IMG_4128.jpeg
    195 KB · Views: 72
  • IMG_4149.png
    IMG_4149.png
    2.8 MB · Views: 74
  • IMG_4159.jpeg
    IMG_4159.jpeg
    1.6 MB · Views: 66
  • IMG_4160.jpeg
    IMG_4160.jpeg
    1.6 MB · Views: 67
Last edited:
Now that is quite the solution for failed supports! I love it! The magnum looks awesome man, keep it up and welcome to the community!
 
Now that is quite the solution for failed supports! I love it! The magnum looks awesome man, keep it up and welcome to the community!

Thanks man! I’m keen to sand and paint once the laser is finished, hopefully it’ll turn out well then too, never been much of a painter haha.

Yeah I was deadset determined, been having issues with my filament absorbing moisture but I now have a dryer, I see more, improved magnums on the horizon, among other things
 
That’s actually crazy that that worked XD

I would have just given in and restarted

Welcome to the community btw!
 
That's a great first prop! Like you said, little sanding and paint and it's going to look really great. And dialing that in on smaller pieces can propel you to success in larger ones. Looking forward to seeing the progress!
 
This thread is more than 8 months old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top