1st Build 3D Printed ODST Build

Status
Not open for further replies.
Update 8: Belt
belt is now all finished and wearable
5402F39A-5006-47BC-A61F-73E11BFAA1BC.jpeg6867EBA7-C7BD-424F-95AC-FEDD47B070C1.jpeg
not the most clear images, quite hard to picture when not wearing
 
Update 8.5
Simple print of the odst combat knife just so I have something to hold in photos whilst I'm also making the leg armour and other parts. Also, I now have a temp visor installed on the helmet for the time being.
0A6FCE17-D585-4171-B853-26EC6FE911EB.pngF69B9158-4295-4306-8525-90281A0BBC9E.png5DDCB7D3-F9FF-4151-90A3-5C4D67830895.jpeg
2B503DB2-303B-4C21-B9C5-5C82FD986037.png
 
Last edited:
Update 9
I'm back to working on the suit after some time away from it, the legs have some work to them but mainly focused on finishing the visor on the helmet.
helmetvisor1.jpgThis was the test print for the size of the visor making sure that it would fit.

My plan was to make a 3d printed visor but modelled with a crack in it so i could see out of it and it looked cool, making it more personal

helmetvisor2.jpghelmetvisor3.jpgUnpainted size test again and ended up using this one for the final thing, also checking i could actually see out of the hole i created

helmetvisor4.jpghelmetvisor5.jpg Painted and fixed in place.

The cracked visor is for my OC Spud the ONI Operative after multiple deployments and shots to the head his visor finally gave in.
 
Update 9
I'm back to working on the suit after some time away from it, the legs have some work to them but mainly focused on finishing the visor on the helmet.
View attachment 307437This was the test print for the size of the visor making sure that it would fit.

My plan was to make a 3d printed visor but modelled with a crack in it so i could see out of it and it looked cool, making it more personal

View attachment 307438View attachment 307439Unpainted size test again and ended up using this one for the final thing, also checking i could actually see out of the hole i created

View attachment 307440View attachment 307441 Painted and fixed in place.

The cracked visor is for my OC Spud the ONI Operative after multiple deployments and shots to the head his visor finally gave in.
I told Spud to DUCK!
 
This is beautiful. Only makes me want to buy a 3D printer more. Can't wait for your next update.
 
Love the build so far. Can I inquire where you got your files? I did a super quick skim and didn't see anything in the update posts.
 
Update 10: Big Update

Only recently realised that I haven't done a post on here in a while so this is going to be a big one

The suits now 95% done, just the back section to be made but I have plans to make the rookies backpack to cover that section eventually.

Shoulder:
The original base ODST shoulder I made has been remade to match the files I used for everything else so that is now painted and on the suit, i only have a picture of unpainted but it is the same as my old one paint wise
IMG_7913.jpegIMG_7917.jpeg
Legs:
The short reply is done.
The long reply is shins and thighs are both made painted and attached to the rest of the suit, the thighs are printed but also have foam as the inside layer which just helps with comfort
IMG_7803.jpegIMG_7804.jpegIMG_7805.jpegIMG_7806.jpegIMG_7834.jpegIMG_7835.jpegIMG_7865.jpegIMG_7866.jpegIMG_7867.jpegIMG_7827.jpeg
Weapon:
I made a new pistol to replace my socom as I wanted something smaller, so I went for the reach magnum printed in one part and then hand-painted it all
IMG_7897.jpegIMG_7907.jpegIMG_7908.jpeg
 
Last edited:
Status
Not open for further replies.
Back
Top