Halo Infinite - 3D Printable Files

Status
Not open for further replies.
IMG_20200807_215938.jpg


Moe, not sure how often you get to see your files fully printed, so here's my 1:6 scale figure.
 
Update: I think I'm done - Halo Infinite - Master Chief Inspired Armor Set - No visor by moesizzlac

Hello all,

I was working with marinesniper on trying to make PDO's from a file by Jonty Schmidt on Youtube. Jonty made a nice model of Master Chief in Blender. In the middle of trying to turn it into pdo's, I figured let's try to make it ready for 3D Printing as well. As usual, not all 3D files are printable at first. Below is my progress so far. Right now, they have all been altered to be solid sheets. They just need wall thickness. I'll release them as soon as they pass my print tests.

View attachment 290831
View attachment 290832
View attachment 290833
View attachment 290834
View attachment 290835
View attachment 290836
View attachment 290837View attachment 290838

Later!
I found a small thing that you could fix to make it more game accurate. The tube on the side is more Halo 3 style than Halo infinite. Otherwise, I love what you’ve done.
 

Attachments

  • C8E07662-51BE-4201-9C57-20959C883607.jpeg
    C8E07662-51BE-4201-9C57-20959C883607.jpeg
    612.2 KB · Views: 263
Update: I think I'm done - Halo Infinite - Master Chief Inspired Armor Set - No visor by moesizzlac

Hello all,

I was working with marinesniper on trying to make PDO's from a file by Jonty Schmidt on Youtube. Jonty made a nice model of Master Chief in Blender. In the middle of trying to turn it into pdo's, I figured let's try to make it ready for 3D Printing as well. As usual, not all 3D files are printable at first. Below is my progress so far. Right now, they have all been altered to be solid sheets. They just need wall thickness. I'll release them as soon as they pass my print tests.

View attachment 290831
View attachment 290832
View attachment 290833
View attachment 290834
View attachment 290835
View attachment 290836
View attachment 290837View attachment 290838

Later!
What fill do we use for the files?
 
I found a small thing that you could fix to make it more game accurate. The tube on the side is more Halo 3 style than Halo infinite. Otherwise, I love what you’ve done.
I have taken that into account on a later iteration. I'll upload that when I get some time later.
1609717950127.png


What fill do we use for the files?
Usually around 10%. The outer wall has all the strength really. They should be 3 deep on each side.
 
Hello all,

I was working with marinesniper on trying to make PDO's from a file by Jonty Schmidt on Youtube. Jonty made a nice model of Master Chief in Blender. In the middle of trying to turn it into pdo's, I figured let's try to make it ready for 3D Printing as well. As usual, not all 3D files are printable at first. Below is my progress so far. Right now, they have all been altered to be solid sheets. They just need wall thickness. I'll release them as soon as they pass my print tests.

View attachment 290831
View attachment 290832
View attachment 290833
View attachment 290834
View attachment 290835
View attachment 290836
View attachment 290837View attachment 290838

Later!
Just some things that you don’t have to do, but would make the files more game accurate. The chest plate has two missing pieces, and in the second pic the two pieces need to be closer together
Update: I think I'm done - Halo Infinite - Master Chief Inspired Armor Set - No visor by moesizzlac

Hello all,

I was working with marinesniper on trying to make PDO's from a file by Jonty Schmidt on Youtube. Jonty made a nice model of Master Chief in Blender. In the middle of trying to turn it into pdo's, I figured let's try to make it ready for 3D Printing as well. As usual, not all 3D files are printable at first. Below is my progress so far. Right now, they have all been altered to be solid sheets. They just need wall thickness. I'll release them as soon as they pass my print tests.

View attachment 290831
View attachment 290832
View attachment 290833
View attachment 290834
View attachment 290835
View attachment 290836
View attachment 290837View attachment 290838

Later!
Just some things that you don’t have to do, but would make the files more game accurate. The chest plate has two missing pieces, and in the second pic the two pieces need to be closer together
 
Update: I think I'm done - Halo Infinite - Master Chief Inspired Armor Set - No visor by moesizzlac

Hello all,

I was working with marinesniper on trying to make PDO's from a file by Jonty Schmidt on Youtube. Jonty made a nice model of Master Chief in Blender. In the middle of trying to turn it into pdo's, I figured let's try to make it ready for 3D Printing as well. As usual, not all 3D files are printable at first. Below is my progress so far. Right now, they have all been altered to be solid sheets. They just need wall thickness. I'll release them as soon as they pass my print tests.

View attachment 290831
View attachment 290832
View attachment 290833
View attachment 290834
View attachment 290835
View attachment 290836
View attachment 290837View attachment 290838

Later!
Just some things that you don’t have to do, but would make the files more game accurate. The chest plate has two missing pieces, and in the second pic the two pieces need to be closer together
 

Attachments

  • 78DD05BC-1C68-4C92-9636-4C60542F4543.jpeg
    78DD05BC-1C68-4C92-9636-4C60542F4543.jpeg
    593 KB · Views: 219
  • A575A3F9-4843-4BE3-B674-B023355D6EFA.jpeg
    A575A3F9-4843-4BE3-B674-B023355D6EFA.jpeg
    727 KB · Views: 222
Just some things that you don’t have to do, but would make the files more game accurate. The chest plate has two missing pieces, and in the second pic the two pieces need to be closer together
I see what you are talking about. some good suggestions from everyone on here. I'm still going to hold off updating until the game is released because I suspect there will be more changes in the future.
 
I see what you are talking about. some good suggestions from everyone on here. I'm still going to hold off updating until the game is released because I suspect there will be more changes in the future.

Here are some photos for if they are in the final cut for the armor. Also, I don’t think that the suit will be changed since they’ve released the demo, toys, helmet, and costumes.
 

Attachments

  • 74E390F9-8095-4F24-B502-AAE0FCC94CAD.jpeg
    74E390F9-8095-4F24-B502-AAE0FCC94CAD.jpeg
    25.8 KB · Views: 240
  • C61BF354-4228-4F5F-B722-5146818565A0.jpeg
    C61BF354-4228-4F5F-B722-5146818565A0.jpeg
    258.3 KB · Views: 262
  • 18E4908A-62E7-4252-9457-5823533BBE54.jpeg
    18E4908A-62E7-4252-9457-5823533BBE54.jpeg
    648.1 KB · Views: 264
Last edited:
I think a nice addition would be a left gauntlet with the grapple and I left the gauntlet without the grapple since the grapple has been confirmed.
I did upload a grapple hook in November of 2020 - both with a solid base and one that can fit right on the forearm.


1615260027877.png


1615260045517.png


1615260141356.png
 
First let me say, these files are absolutely beautiful. I have been playing around with them, I was hoping to unfold them in pepakura to do an old-fashioned fiberglass build but am having trouble, the high-detail (and subsequently high poly) of the models unfolds into a monstrosity. Does anyone have any tips on how I could go about doing this?
 
I see what you are talking about. some good suggestions from everyone on here. I'm still going to hold off updating until the game is released because I suspect there will be more changes in the future.
I know you said that you didn't want to update it until the game is released, but I think it would be a good idea to update it around September or October, (since it has been confirmed that Infinite will be released this November) so we can print it out before the game comes out. If not, thank you anyway.
 
Another part that I found that you can add whenever you decide to is the detail behind the back is missing. The third one is from the fortnite game files.
 

Attachments

  • Screenshot (204).png
    Screenshot (204).png
    134.4 KB · Views: 247
  • Screenshot (204)_LI.jpg
    Screenshot (204)_LI.jpg
    887.5 KB · Views: 254
  • Screenshot (206).png
    Screenshot (206).png
    160.3 KB · Views: 219
Last edited:
First let me say, these files are absolutely beautiful. I have been playing around with them, I was hoping to unfold them in pepakura to do an old-fashioned fiberglass build but am having trouble, the high-detail (and subsequently high poly) of the models unfolds into a monstrosity. Does anyone have any tips on how I could go about doing this?
Check out Post #3 here: 3d and pep kicking my butt

They are not unfolded yet but are a fair bit better than starting with my 3D files.
 
Check out Post #3 here: 3d and pep kicking my butt

They are not unfolded yet but are a fair bit better than starting with my 3D files.
Thank you, I appreciate you linking me to those files. Unfortunately I love the incredible detail of your models too much, I'm not really a fan of the lack of the same in those other files, they appear rather inaccurate to me. I ended up using 3ds max and reducing the polygon count to something decently manageable. It was a difficult unfold, and will also be a difficult pepakura, but not impossible. Currently working on gluing it together! :)
 
Status
Not open for further replies.
Back
Top